2 0 0 2
VOLVO
C70 Coupe & Convertible
| INDEX |
HomeLink® is an advanced system that can be programmed to learn the codes of three different remote controlled-devices (e.g., garage door openers, remote lighting, entry door lock). HomeLink®'s sun visor-mounted transceiver, powered by your car's electrical system, may then be used in place of your hand-held remote controls.
NOTE: For your security, the HomeLink® Universal Transceiver is designed to not function if you lock your car from the outside.
Programming the transceiver
1. The ignition switch must be turned to the "accessory" position (II)
before programming the HomeLink® Universal Transceiver.
Release the buttons.
2. Begin by erasing all 3 factory default channels. Hold down the two outside buttons (buttons 1 and 3 in the illustration) on the HomeLink® Universal Transceiver for about 20 seconds, until HomeLink® 's indicator light begins to flash. Then release the buttons.
3. Hold your hand-held transmitter (garage door opener, for example) 2 to 5 in. (5 to 12 cm) away from the HomeLink® surface, keeping the indicator light in view. For placement questions, contact HomeLink® toll-free 1-800-355-3515 (Internet: www.HomeLink.com).
4. Using two hands, push and hold both your hand-held transmitter's button and the transceiver button you wish to program. The indicator light will flash first slowly, then rapidly. Rapid flashing tells you the HomeLink® button has been successfully programmed. Release both buttons.
5. If you are programming a rolling code-equipped device (e.g., garage door opener or entry door lock), refer to "Programming rolling codes" on the next page to complete the programming process.
Repeat steps 3 and 4 to program the other two transceiver buttons. If, after several attempts, you are unable to successfully train the HomeLink® Universal Transceiver to learn your hand-held transmitter's signal, contact HomeLink® toll-free 1-800-355-3515 (Internet: www.HomeLink.com).
WARNING!
· If you use HomeLink® to open a garage door or gate, be sure no one is near the gate or door while it is in motion.
· Do not use the HomeLink® Universal Transceiver with any garage
door opener that lacks safety "stop" and "reverse" features as required
by federal safety standards. (This includes any garage door opener
model manufactured before April 1, 1982) A garage door opener that
cannot "detect" an object, signalling the door to "stop" and "reverse"
does not meet current federal safety standards. Using a garage door
opener without these features increases the risk of serious injury or
death. For more information on this matter, call toll-free 1-800-355-
3515 (Internet: www.HomeLink.com).
During programming, your hand-held transmitter may automatically stop transmitting. To successfully train HomeLink® , continue to hold the HomeLink® button. At the same time, repeatedly press and hold your hand-held transmitter's button at two-second intervals until HomeLink® has learned your transmitter's code. The HomeLink® indicator light will flash first slowly, and then rapidly to indicate that the button has been successfully programmed.
Determining if your garage door uses a rolling code
Determining if your garage door uses a rolling code Determine, in one of the following ways, if your garage door uses a rolling code system and is manufactured after 1996:
To train a rolling code garage door opener , follow these instructions after programming the desired transceiver button according to "Programming the transceiver." The help of a second person may make training easier.
1. Locate the training button on the garage door opener motor head unit. The location and color of the training button may vary. If you encounter difficulty, refer to the garage door opener owner's manual or call toll-free 1-800-355-3515 (Internet: www.HomeLink.com).
2. Press the "training" button on the garage door opener motor head unit until the "training" light comes on.
3. Press and release the programmed HomeLink® button. Press and release the programmed HomeLink® button a second time to complete the training process. Some garage door openers may require you to do this procedure a third time to complete the training.
The programmed button on your HomeLink® Universal Transceiver
should now operate your garage door opener. The original hand-held
transmitter can also be used, as desired, to operate the garage door. Operating the HomeLink® Universal Transceiver
Once programmed, the HomeLink® Universal Transceiver can be used
in place of your hand-held transmitters.
To operate, the key must be turned to the "accessory" position (II) or the
engine must be running. Press the programmed HomeLink® button to
activate the garage door, driveway gate, security lighting, home security
system, etc.
Your original hand-held transmitters may, of course, be used at any time.
Erasing programmed buttons
Individual buttons cannot be erased. To erase all three
programmed buttons:
1. 1. Turn the ignition key to the "accessory" position (II).
2. Hold down the two outside buttons on the HomeLink® Universal
Transceiver for about 20 seconds, until HomeLink® 's indicator light
begins to flash.
3. Release both buttons.
The HomeLink® buttons can be reprogrammed using the
procedures described on the previous page.
(HomeLink® information is continued on the next page)
Reprogramming a single HomeLink® button
1. Press and hold the desired HomeLink® button.
Do not release the button until step 3 has been completed.
2. When the indicator light begins to flash slowly (after
approximately 20 seconds), position the hand-held transmitter 2 to 5 in. (5 to
12 cm) away from the HomeLink® surface.
3. Press and hold the hand-held transmitter button. The previously programmed device has now been erased and the
new device can be activated by pressing the HomeLink® button that has
just been programmed. This procedure will not affect any other
programmed HomeLink® buttons.
NOTE:
· Retain the original transmitter(s) for future programming
procedures (i.e., if you purchase a new car).
· It is also suggested that if you sell your car, the
programmed channels on the HomeLink® Universal Transceiver be erased
for security purposes.
The HomeLink® indicator light will begin to flash, first
slowly then rapidly. When the indicator light flashes rapidly, release
both buttons.
