pg. 92 Replacing bulbs




Insert a screwdriver and turn

Vanity mirror

· Switch off the ignition.

· Insert a screwdriver under the lower edge and turn to loosen the glass lens.

· Pull out the bulb and replace it.

· Press the lower edge of the lens into place above the four catches.

· Press the upper edge of the lens into place.



Trunk/cargo compartment light

· Press in the catch with a flat screwdriver and remove the lens.

· Pull the bulb out of the holder and replace it.

· Press the glass lens into position.


Replacing number plate lighting - V 40
Switch off all lights and remove the ignition key. Remove the screws and take out the lamp housing. Replace bulb. Reinstall and screw the lamp housing into place again. NOTE: Other bulbs may be difficult for the owner to replace. Let your Volvo retailer replace these bulbs if necessary.

pg. 93 Replacing fuses



Fuse removal tool in passenger compartment fuse box


Replacing fuses

If an electrical component fails to function, it is likely that a fuse has blown due to a temporary circuit overload.

The fuse boxes are located in the engine compartment (see page 94) and in the passenger compartment (see page 95).

A label on the inside of each cover indicates the amperage and the electrical components that are connected to each fuse.
Defective fuse Intact fuse

The easiest way to see if a fuse is blown is to remove it. Pull the fuse straight out. From the side, examine the curved metal wire to see if it is broken. If so, put in a new fuse of the same color and amperage (written on the fuse). Spare fuses are stored in the fuse box cover. If fuses burn out repeatedly, have the electrical system tested at a Volvo retailer. If you find it difficult to remove a fuse, you will find a special fuse tool clipped in the fuse box.

pg. 94 Fuses





NOTE: If a trailer hitch has been installed, two supplementary fuses will be added to the cable harness near the right tail light.


Fusebox, Passenger compartment
No. Components Amperage
1 Blower motor, ECC 25
2 Cigarette lighter, Accessories 20
3 Accessories, Power windows, Power mirrors 10
4 ECM for DSA/ABS/CEM. 10
5 Seat heating 20
6 Illumination of switches: Winter, DSA back-up lights, CEM, Turn indicators 15
7 Cruise control, Shiftlock, SRS, Alarm 10
8 Hazard warning flasher, Central doorlock activated, flasher 15
9 Audio system, Cigarette lighter, Accessories 15
10 Wiper/Washer front 20
11 SRS, ECM for DSA/Engine/Transmission, Combined instrument panel, Immobilizer 10
12 Sun roof, heater/AC, Alarm, Seatbelt reminder 15
13 OBD II connector, Brake lights 15
14 Front wiper, headlamp wipers, Wiper/washer rear 20

pg. 95 Fuses





Fusebox - Engine compartment
No. Components Amperage
1 ........... 120
2 Supply to fuses 11/B 1,2,8 and 13 40
3 ........... ...
4 ........... ...
5 Rear window and side-mirror heaters 25
6 Driver's power seat 25
7 ........... ...
8* ECC, courtesy lights, ignition lock, Siren, Combined instrument panel 10
9* Central locking, alarm 20
10* Audio 15
11 ECM for immobilizer. engine relays 20
12 Power windows, Power mirrors 30
13 Radiator fan 30
14 Starter motor, supply to fuses 11/B 3-7, 9-12 and 14 40
15 ABS 50
16 Reserve --
17 Fuel pump 15
18 Engine components 10
19 Foglights 20
20 Reserve --
21 High beam L 15
22 High beam R 15
23 Parking lights 10
24 Parking lights 10
25 TCM 10
26 ........... .....
27 Electric socket rear 15
28 Main light 15
29 Horn 15
30 Charger AC, fan AC 15
31 VAC pump (AT) 10
32 Reserve --

*To be able to remove these fuses, you must FIRST PULL UP the yellow fuseholder (transport fuse) by hand and then use the special fuse tool to remove the fuse. See page 93.

NOTE: Before you pull up the transport fuse holder, make sure that you know the radio code, since this code will be erased from the radio when pulling up the fuseholder!

pg. 96 Replacing wiper blades



Replacing wiper blades

Lift the wiper arm off the windshield and hold the blade at right angles to the arm. Pinch the end of the plastic clip located at the back of the arm.




Slide the wiper blade along the arm to release it from the hook.




Install the new blade (installation is the reverse of removal) and make sure that it is properly attached to the wiper arm.



NOTE: For reasons of safety, you should change the windshield wiper blades as soon as they start to leave marks on the windshield or fail to wipe efficiently and cleanly.

To obtain maximum lifetime from a set of wiper blades, clean them with a stiff-bristle brush and warm, soapy water as part of a normal car wash.

short end towards grille

Replacing headlight wiper blades (certain models)

Pull the wiper blade in the direction indicated by the arrow in the illustration to remove it. Press the new wiper blade into place. Check that the new blade is properly attached to the wiper arm.

Cleaning the outside of the windshield and wiper blades

If the windshield/tailgate is not clear after using the wiper(s) or if the blade chatters when running, wax or other material may be on the blade or on the surface of the glass.

Clean the glass with a suitable cleaning agent. The glass is clean if beads do not form when you rinse it with water.

Clean the wiper blade by wiping vigorously with a cloth soaked in full strength windshield washer solvent. Then rinse the blade with water.

Wiper blades should be checked on a regular basis and replaced when worn.

pg. 97 In case of emergency




Shiftlock override button

Shiftlock release

The gear selector is locked in the (P)ark position. To manually release the shiftlock:

· Turn the starting (ignition) key to position I

· Press firmly on the "SHIFTLOCK OVERRIDE" button located at the base of the gear selector

· While holding the override button down, press the button on the front of the gear selector

· Move the selector from the (P)ark position.



Manually operating the fuel filler door

If the fuel filler door does not unlock together with the central locking system:

- Remove the plastic cover in the storage area on the left side of the trunk.

- Pull the eyelet firmly

pg. 98 In case of emergency




Manually closing the sun roof

To manually close the sun roof, use the socket wrench supplied in the tool kit (see page 84).

· Remove the courtesy light lenses.
· Undo the screws and remove the courtesy light cover.
· Remove the cap from the screw with the screwdriver.
· Remove the screw (1), washer (2), spacer(s) (3) and collar.
· Turn the screwdriver back into the handgrip to make it into a socket wrench. Fit this onto the sun roof motor drive shaft and close the sun roof by turning clockwise.

NOTE:

If you wind too far, the sun roof will move into the ventilator position. Rewind until the roof shuts again.



Previous Page   Next Page

Contents | Top of Page