pg. 155 Audio system SC-816 (certain models)

The following pages describe the use of your SC-816



1. On/off (push)
2.

  • Volume (turn)
  • Pause/Mute (push)
  • Balance (pull)
    3. CD mode selector - Active sound control (single)
    4. CD changer selector
    5.
  • Tape mode selector
  • Tape direction selector PROG
    6. Bass control
    7. Treble control
    8. Fader control
    9.
  • Preset buttons
  • CD-Disc No. selector
    10. Dolby B NR button
    11. CD-random play
    12. Cassette eject
    13. Not in use
    14. Scan
    15. Auto seek memory
    16.
  • Seek tuning up/down
  • TP -Next/Previous song
  • CD -Next UP/Previous DOWN track
    17.
  • Manual tuning
  • TP -fast forward/Rewind
  • CD -Music search UP/DOWN
    18. CD eject (single)
    19. CD slot
    20. Cassette slot
    21. Display
    22. Waveband selector (AM)
    23. Waveband selectors (FM)
    24.
  • Anti-theft LED
  • Disc in LED (single)


    TP = Applicable only in Tape Mode


    CD = Applicable only when in CD mode and connected to a CD changer.

    pg. 156 Anti-theft code


    Anti-theft code


    The radio features anti-theft circuitry. If the set is removed from the vehicle or if the battery power is disconnected, a special code must be entered to enable operation of the set.
    Refer to the radio code card supplied with your vehicle or ask your retailer for the correct code.
    When the car is parked with ignition key removed the anti-theft LED will flash.


    To enter the code


    After installation or when the set has been disconnected from power, the set displays "CODE" when it is switched on.
    Enter the 4-digit code using the preset buttons.
    If the correct code is entered the set is entered the set is ready to use.
    If you enter an incorrect code you must enter the correct code again from the beginning.


    Incorrect code


    If an incorrect code has been entered "EEEE" is displayed. Enter the correct code. After three unsuccessful coding attempts the set will lock and remain locked for two hours.
    "OFF" is displayed.
    During this waiting period:

  • the battery must be connected
  • the ignition key must be turned to position I
  • the unit must be turned on
    Make sure the headlights are turned off to help prevent battery drain (please refer to page 20 for information on turning the headlights off). Enter the code again once this time has elapsed.

    pg. 157 Radio SC-816


    A - On/off switch


    Push the button to switch on the radio. Press the button to turn the radio off.


    B - Volume control


    Turn the button clockwise to increase the volume. The volume control is electronic and has no end stop.


    C - Waveband selector


    The desired waveband is set by pressing one of the waveband selector bands. The frequency and waveband is shown on the display.


    NOTE: There are two FM wavebands and one AM waveband. This makes it possible to store 2 x 6 FM stations and 6 AM stations in memory.


    D - Setting frequency selection


    The radio can be used in most parts of the world by changing the frequency selection intervals as follows:
    Depress and hold preset button 5 and turn the radio ON. "USA" will flash on the display. Each time button 5 is pressed, the frequency selection will change from "USA" to "AUS", etc. When the correct country name is displayed, wait 5 seconds and the radio will be ready for use.


    E - Manual tuning


    Press the left side tune button to tune to lower frequencies and the right side to tune to higher frequencies. The tuned frequency is displayed.


    ST will be displayed to indicate stereo FM reception.

    pg. 158 Radio SC-816 (cont.)


    A - Seek tuning up/down


    Press the left side tune button to tune to lower frequencies and the right side to tune to higher frequencies. The radio seeks the next audible station and stops there. If you wish to continue the seek tuning, press the tune button again.


    B - Preset programming


    1. Tune to the desired frequency.
    2. Depress and hold a preset button. The audio will cut out. Keep the button depressed until the audio comes on again (approx. 2 seconds).
    3. The frequency is now stored on this present button.


    C - Preset buttons


    To select a pre-programmed radio frequency, depress the preset button. The set frequency will be displayed.

    pg. 159 Radio SC-816 (cont.)


    A - Automatic programming (Auto)


    Please note that this function will not interfere with pre-stored stations on buttons 1-6.
    This function automatically seeks and stores up to 8 strong AM or FM stations.
    This is especially useful when travelling in areas where radio stations are unfamiliar.
    1. Depress and hold the "AUTO" button for at least 1 second . A number of strong stations (max. 8) on the chosen waveband are now automatically stored in the memory.
    The lowest frequency station is heard. If there are no audible stations, "- - - -" is displayed.
    2. Press the "AUTO" button ( for less than 1 second ) to obtain another autostored station.
    A new station will be selected each time the button is pressed momentarily.


    B - Bass control


    Adjust the bass by sliding the control up or down (up to increase, down to decrease). A "detent" indicates "equalized" bass.


    C - Treble control


    Adjust the treble by sliding the control up or down (up to increase, down to decrease). A "detent" indicates "equalized" treble.

    pg. 160 Radio SC-816 (cont.)


    A - Fader control


    Adjust front/rear speaker balance by sliding the control up or down.
    (Up to direct more sound to the front speakers, down to direct more sound to the rear speakers.
    The "detent" indicates "equalized" front/rear balance position.


    B - Pause function


    Press the "volume" knob to temporarily mute the sound. "PAUSE" is displayed.


    C - Balance control


    Pull out the "volume" knob and adjust the left/right balance by turning the knob counter-clockwise or clockwise.


    D - Scan


    Press this button to listen to each station for five seconds. Press it again to stop scanning.


    E - Active sound control (ASC)


    The ASC function automatically adjusts the volume level of the audio system according to driving speed.
    To deactivate ASC depress the "CD" button until "ASC" is no longer displayed.
    To activate ASC, depress the "CD" button until "ASC" is displayed (approx. 2 seconds).




    Previous Page  Next Page

    Contents | Top of Page