pg. 1:25 Audio system, General description

The following pages describe the use of your SC-810 Cassette Radio and CD remote control


  • On/off (turn)
  • Volume (turn)
  • Pause/Mute (push)
    2. CD mode selector
    3. Bass control
    4. Treble control
    5. Fader control
    6. Waveband selectors (FM)
    7. Waveband selectors (AM)
    8. Preset buttons, CD-Disc No. selector
    9. Autostore memory (FM)
    10. Autostore memory (AM)
  • Manual tuning
  • Seek tuning (push)
    12. Tape direction selector REV, CD-Random play
    13. Cassette eject
    14. Display
    15. Cassette slot
    16. TP -Next song
    CD -Next track UP
    17. TP -Fast forward
    CD -Music search UP
    18. TP -Rewind
    CD -Music search DOWN
    19. TP -Previous song REPEAT
    CD -Previous track DOWN
    20. Tape mode selector

    TP = Applicable only in tape mode
    CD = Applicable only when in CD mode and connected to a CD changer

    pg. 1:26 Anti-theft code

    Anti-theft code

    The radio features anti-theft circuitry. If the set is removed from the vehicle or if the battery power is disconnected, a special code must be entered to enable operation of the set. Refer to the radio code card supplied with your vehicle or ask your retailer for the correct code .
    When the car is parked with the ignition key removed, the anti-theft LED will flash

    To enter the code

    After installation or when the set has been disconnected from power, the set displays "codE" when it is switched on.
    Enter the 4-digit code using the preset buttons. If the correct code is entered, "on" is displayed and the set is ready to use.
    If you enter an incorrect code you must enter the correct code again from the beginning.

    Incorrect code

    If an incorrect code has been entered "rPt" is displayed. Enter the correct code.
    After three unsuccessful coding attempts the set will lock and remain locked for two hours.
    "OFF" is displayed.

    During this waiting period:

  • the battery must be connected
  • the ignition key must be turned to position I
  • the unit must be turned on
    Make sure the headlights are turned off to help prevent battery drain.
    Enter the code again once this time has elapsed.

    pg. 1:27 Radio

    A - On/off switch and volume control

    Turn the button clockwise to switch on and to increase the volume.

    B - Waveband selector

    The desired waveband is set by pressing one of the waveband selector buttons. The frequency and waveband is shown on the display.

    NOTE: There are two FM wavebands and two AM wavebands. This makes it possible to store 2 x 6 FM stations and 2 x 6 AM stations in memory.

    C - Setting frequency selection

    The radio can be used in most parts of the world by changing the frequency selection intervals as follows:
    Depress and hold preset button 5 and turn the radio ON. "USA" will flash on the display. Each time button 5 is pressed, the frequency selection will change from "USA" to "AUS", etc. When the correct country name is displayed, wait 5 seconds and the radio will be ready for use.
    When "USA" is chosen, the FM band will search for stations in 200 kHz intervals and AM will search in 10 kHz intervals.

    D - Manual tuning

    Turn the knob counter-clockwise to tune to lower frequencies and clockwise to tune to higher frequencies. The tuned frequency is displayed.

    pg. 1:28 Radio

    A - Seek tuning

    Push the tuning knob to seek for higher frequencies. The radio seeks the next audible station and stops there. If you wish to continue the seek tuning, press the tuning knob again.

    B - Preset programming

    1. Tune to the desired frequency.
    2. Depress and hold a preset button. The audio will cut out. Keep the button depressed until the audio comes on again (approx. 2 seconds).
    3. The frequency is now stored on this preset button.

    C - Preset buttons

    To select a pre-programmed radio frequency, depress the preset button. The set frequency will be displayed.

    pg. 1:29 Radio

    A - Automatic programming (Autostore)

    This function automatically seeks and stores up to 8 strong AM or FM stations. This is especially useful when traveling in areas where radio stations are unfamiliar.
    1. Depress and hold one of the "auto store" buttons for at least 1 second. A number of strong stations (max. 8) on the chosen waveband are now automatically stored in the memory. If there are no audible stations, "no" is displayed.
    2. Press one of the "auto store" buttons (for less than 1 second) to obtain another autostored station. A new station will be selected each time one of these buttons is pressed.

    B - Bass control

    Adjust the bass by sliding the control up or down (up to increase, down to decrease). A "detent" indicates "equalized" bass.

    C - Treble control

    Adjust the treble by sliding the control up or down (up to increase, down to decrease). A "detent" indicates "equalized" treble.

    pg. 1:30 Radio

    A - Fader control

    Adjust front/rear speaker balance by sliding the control up or down.
    (Up to direct more sound to the front speakers, down to direct more sound to the rear speakers).
    The "detent" indicates "equalized" front/rear balance position.

    B - Mute function

    Press the "power-volume" knob to temporarily mute the sound. "PAUSE" is displayed.

    Previous Page  Next Page

    Contents | Top of Page